anyone installed Mugen Visor
#2
I just installed mine this past weekend and took some pictures. I'll upload them Wednesday sometime. I'll try to scan the instructions. I had my co-worker who is Japanese write some translations for some things. So it made it a little easier to understand. It's an intuitive installation though. Not too difficult. It took me about an hour to do it all.
#4
Originally Posted by t-bone
I just installed mine this past weekend and took some pictures. I'll upload them Wednesday sometime. I'll try to scan the instructions. I had my co-worker who is Japanese write some translations for some things. So it made it a little easier to understand. It's an intuitive installation though. Not too difficult. It took me about an hour to do it all.
#5
Here are some pictures I took. I'll post up the partially translated instructions later tomorrow.
The box of clips with the pins to hold the clip onto the visor.
One clip attached to the visor.
Masking tape applied onto the back of the adhesive strips. This helps in the removal of the tape.
The packet of a towelette soaked in toluene. This helps promote the adhesion of the tape onto the surface you wipe with the toluene after you clean the area with isopropyl alcohol.
Here are two pictures of the window lining pulled down to expose the sill to enable you to push the clips onto the window sill.
Once you position the visor on then you need to push the window lining back into place. This will help hold the visor in place before you remove the tape and allow you to maintain the position of the visor on the door.
It was noted in the instructions that you wanted the visor 2mm below the top edge of the door. The instructions that I'll scan later show this.
And here are some pictures of the final look. I need to tint my windows still.
The box of clips with the pins to hold the clip onto the visor.
One clip attached to the visor.
Masking tape applied onto the back of the adhesive strips. This helps in the removal of the tape.
The packet of a towelette soaked in toluene. This helps promote the adhesion of the tape onto the surface you wipe with the toluene after you clean the area with isopropyl alcohol.
Here are two pictures of the window lining pulled down to expose the sill to enable you to push the clips onto the window sill.
Once you position the visor on then you need to push the window lining back into place. This will help hold the visor in place before you remove the tape and allow you to maintain the position of the visor on the door.
It was noted in the instructions that you wanted the visor 2mm below the top edge of the door. The instructions that I'll scan later show this.
And here are some pictures of the final look. I need to tint my windows still.
#7
Originally Posted by sy11580
Thank yOu so much T-Bone!!
I have a question the clip seem like block the windows goes all the way up!! how can u push back the windows lining???
I have a question the clip seem like block the windows goes all the way up!! how can u push back the windows lining???
#8
Very Nice T-Bone,
Wondering, why mine Mugen Visors doesn't come with the clips.
Mine has the Double side 3M Tape. Does your come with Double Side Tape?
No Instruction how to install them either. WTF
Kevin L
Wondering, why mine Mugen Visors doesn't come with the clips.
Mine has the Double side 3M Tape. Does your come with Double Side Tape?
No Instruction how to install them either. WTF
Kevin L
#9
Originally Posted by Titans
Very Nice T-Bone,
Wondering, why mine Mugen Visors doesn't come with the clips.
Mine has the Double side 3M Tape. Does your come with Double Side Tape?
No Instruction how to install them either. WTF
Kevin L
Wondering, why mine Mugen Visors doesn't come with the clips.
Mine has the Double side 3M Tape. Does your come with Double Side Tape?
No Instruction how to install them either. WTF
Kevin L
#10
Originally Posted by Titans
Very Nice T-Bone,
Wondering, why mine Mugen Visors doesn't come with the clips.
Mine has the Double side 3M Tape. Does your come with Double Side Tape?
No Instruction how to install them either. WTF
Kevin L
Wondering, why mine Mugen Visors doesn't come with the clips.
Mine has the Double side 3M Tape. Does your come with Double Side Tape?
No Instruction how to install them either. WTF
Kevin L
I hope yours are genuine Mugen and not the fake ones. Where did you buy them from? Did they come in the Mugen box that looked like this?
#12
Originally Posted by Titans
Nope, It doesn't look like that.
Mine came in today like Used Visors, one with 3" crack WTF.
I got them from this Forum, but I am not going Name That Vendor yet.
I have to get it clear.
Mine came in today like Used Visors, one with 3" crack WTF.
I got them from this Forum, but I am not going Name That Vendor yet.
I have to get it clear.
#13
AJ is selling for CAD$169 I think
real Mugen comes with a nice box of clips,insructions, the 3M cleaning thing and the double sided tape doesn't have 3M on it, its like orange colour tape, each visor has 2 holes drilled so you can use the plastic plugs to plug in the metal clips
real Mugen comes with a nice box of clips,insructions, the 3M cleaning thing and the double sided tape doesn't have 3M on it, its like orange colour tape, each visor has 2 holes drilled so you can use the plastic plugs to plug in the metal clips
#17
Originally Posted by Titans
I paid $90.96 Cad for it.
It was a special Deal as I was told.
I don't mine paying little more for the Original one, but Fock.
It was a special Deal as I was told.
I don't mine paying little more for the Original one, but Fock.