i have a cordless drill with drill bits, ill bring that.

 

Wrench Meet at accordintakeguy's casa Sept 6th @ roughly 10.30 am!

1. accordintakeguy (Jason)
2. gimme (Dan)
3. junior40er (adrian)
4. los_creeper (dave)
5. jazn (jason)
6. Lunar_gd3 (Eddy)
7. Fitting (Ken)
8. JamesBizzle... put me down as a Maybe...
9.
10.

I'll be installing a T1R crank pully, and some J's inner fender braces as well as a new driver side fender (maybe passenger side too), and a duck bill spoiler.

I got a J's LSD, T1R clutch, Greddy guages, and T1R Guage pod that need to go in too, but I doubt you guys will wanna help with that. lol.... but seriously, if any of you guys ARE down lemme know!!!

 

for stuff of that nature, i would rather do it at my house. That way i have every tool available to me.


as for the meet itseld, i will bring my compressor, impact, drill and other miscellaneous tools.

 

score. +rep for gimmie

 

i think ill probably come... can anybody help me install some LEDs i know .. im a newb lolz it's too confusing for me ....

these mods :
https://www.fitfreak.net/forums/fit-...iy-w-pics.html

https://www.fitfreak.net/forums/fit-...ome-light.html

probably get some springs also... can anybody help me with these mods ... im pretty new to everything never been to a meet until i heard about this in a thread i live in RH pretty close by also!

 

Im sure we can, most of these guys have them anyways. Add your name to the list =)

 

pshh, I'll drive to your house if you really will help me. it'll take hours though.. agh..

 

haha dood, just come on the 6th, i wont have much to do, and the more people the better, im sure we can get a few things on your car and out of your room... Dooont trip.

 

1. accordintakeguy (Jason)
2. gimme (Dan)
3. junior40er (adrian)
4. los_creeper (dave)
5. jazn (jason)
6. Lunar_gd3 (Eddy)
7. Fitting (Ken)
8. JamesBizzle... put me down as a Maybe...
9.cKranez(MuthA ****in' Andrew!)
10.

edit we gonna have a bbq or somep if so i can bring some food...

 

i did a motor swap (b18b to b18c1) in 6 hours....dropping the tranny can't be that bad. as far as the LSD...never done one, wont hurt to start

but i would like to wait til the weather cools down a bit. the long jobs + heat = no fun

 

oo yeah guys btw anybody got some xtra laminx yellow fog light film that they can bring i can buy lolz? im running the nokyha yellow fog bulbs would b nice if i added some film also?

 

i'm 50/50 on getting a kraftwerks sc. anyone here capable (and patient enough) to do an install like that?

cheapest install center on kraftwerks' website was charging $725 w/ before & after dyno pulls...

 

I have laminx and nokyas and they are bad ass... as we learned.. dont leave them on while your car is sitting in one spot for too long, because they film will start to smoke after a bit, but while driving they should be well ventilated!

 

Just order one 4x8 sheet, that will do both sides. You should well get it before next month.

 

ok ill order that and some leds !

 

dude, tell me the day and I'll be at your house!

I'll buy you a 12 pack of beer and lunch, and probably dinner too cause it'll take a few hours lol.

 

Well I have the leds wired to my dome, very easy to do. I also just ordered blue Led's for the hvac so ill be taking care of that there. if you wanted to do your car Id help you out. Just make sure to get all your lighting and wiring before hand.

 

The first time I saw it smoke (which is very little) I was like "is my foglight on fire WTF!!"

 

hahahah yea, we were takin pics on top of the parking garage last Wednesday after the NRH meet, and we did a headlight pic, and chris is like... your fogs are smoking! so i just left them off the rest of the time. It started a good 5 to 10 minutes after i had them on.

 

I started using a conditioner from Lamin x when I wash, seems to help a little bit. I read somewhere on fitfreak that they make a thinner cover to help release more heat and help prevent the burning, might be a option for when we eventually burn them up, or blacken the center out.