What did you do to your GK Fit today?
#2526
Well, I have had my 2019 Sport CVT about a week and a half now and have done these few things
Kuga 3D floor mats
SuperBright LEDs headlight bulbs
Pilot Sport mini antenna
Weathertech front window reflectors.
To do:
Have to install my HFP rear spoiler, yellow foglight film, iJDMTOYS rear pillar leds, catch can and waiting for my Bisimoto pulse chamber to show up as that is my priority! I need a little noise as it kills me to drive a quiet car!
Also trying figure out if I want a Takeda intake or something else. This is fun
Kuga 3D floor mats
SuperBright LEDs headlight bulbs
Pilot Sport mini antenna
Weathertech front window reflectors.
To do:
Have to install my HFP rear spoiler, yellow foglight film, iJDMTOYS rear pillar leds, catch can and waiting for my Bisimoto pulse chamber to show up as that is my priority! I need a little noise as it kills me to drive a quiet car!
Also trying figure out if I want a Takeda intake or something else. This is fun
#2529
Last edited by Elcid43; 12-01-2019 at 09:39 PM.
#2530
honestly I didn’t take them out. I just pulled the bulb and wiring from under its easy access. But I’ve pulled the bumper off before to install the red H badge and it wasn’t too bad tbh.
#2532
Thanks guys, will give it a go. I tried to pop it out the other day with a butter knife wrapped it tape but was nervous about breaking something on a car with 300 miles on it. I will be a little more confident this time. Hopefully the first snow of the season dissappears quickly
#2533
This is the passenger side, which in the GK's at least a bit more tedious since there is WAY LESS space to tinker with....
As soon as i recieve the fog lamp covers and do the drivers side, ill do another slide show...🤪😬
Spectre 90⁰ bend and flexible intake tube
Spectre 90⁰ bend
Drank a beer in the process 😬
Used a 2¾ or 2⅞ hole saw... cant really recall the size
Testing the 90⁰ bend on hole i made
The shinny dot is the 90⁰ bend viewed from the front bumper as I fit tested
Routed the Spectre flexible "intake" duct along the underside plastic cover, will hold them in place with some mighty heavy duty cable tie wraps
Almost, almost finished, as soon as the fog lamp covers arrive....
Fog lamp / \"brake duct cooling intakes" arrived!
Inside look.... those are the connecting rubbers from the flexible intake...
How it looks once installed... in this pic i haven't installed the flexible part...
That's how it looks now....
As soon as i recieve the fog lamp covers and do the drivers side, ill do another slide show...🤪😬
Spectre 90⁰ bend and flexible intake tube
Spectre 90⁰ bend
Drank a beer in the process 😬
Used a 2¾ or 2⅞ hole saw... cant really recall the size
Testing the 90⁰ bend on hole i made
The shinny dot is the 90⁰ bend viewed from the front bumper as I fit tested
Routed the Spectre flexible "intake" duct along the underside plastic cover, will hold them in place with some mighty heavy duty cable tie wraps
Almost, almost finished, as soon as the fog lamp covers arrive....
Fog lamp / \"brake duct cooling intakes" arrived!
Inside look.... those are the connecting rubbers from the flexible intake...
How it looks once installed... in this pic i haven't installed the flexible part...
That's how it looks now....
Last edited by elkaku; 12-18-2019 at 04:58 PM.
#2534
No useful pictures, but changed the starter today. Once I figured out how to reach the top bolt, ended up being a relatively easy job. Had to remove four sensor wires at the top of the harness in front of the engine, but didn't have to remove the coolant tank or oil filter to get the starter out once the bolts were removed.
#2540
Very nice, looks good 👍. What wheels are those?