Blackvitzrs GE's progress
#41
I will share one picture so far. Wasn't too happy with this photoshoot before the car got rear ended so I will just post one. I have kinda cheated and parked on a slope. Car is not that low.
#43
it is held on my 3M tape. But because there are two "bumps" on the top part of the hatch where the stock bolt holes are, the spoiler won't sit flush. You have to drill two holes without puncturing the aftermarket spoiler that correspond to the factory bolt holes in order for the wing to sit flush so that 3M tape will hold it in place.
#47
say HI next time!!
I bought it from japanparts.com. It was quite a hefty amount, though insurance covered it. Even if they didn't cover it, it is well worth the money in terms of quality. I doubt even OEM can beat the quality of these lights.
I bought it from japanparts.com. It was quite a hefty amount, though insurance covered it. Even if they didn't cover it, it is well worth the money in terms of quality. I doubt even OEM can beat the quality of these lights.
#48
is quite expensive..... but looks very nice!!!! have to save up some $$ for this!!!
just brought coilover no $$ lu....
one more thing where did yo pick up your SPC front camber bolts!!!
when lowered do we need one for rear wheel??
just brought coilover no $$ lu....
one more thing where did yo pick up your SPC front camber bolts!!!
when lowered do we need one for rear wheel??
Last edited by j's_fit; 07-15-2011 at 01:51 PM.
#52
Hey blackvitzrs,
You have a very nice GE Fit. I was wondering on the fitment on the JDP diffuser, as some other members have said its not 100%. That there's a minor, very minor gap on the passenger side.
Also, what about the quality of the CF and clear coat? Has it hold up? Any bubbling?
And finally. Is it true that the fitment is very tight, which could potentially scratch the paint, and that you have to drill holes to make it fit properly?
Im asking because a different made this comments and I would like to see if this is the same with everyone.
I would appreciate a reply. Thanks.
You have a very nice GE Fit. I was wondering on the fitment on the JDP diffuser, as some other members have said its not 100%. That there's a minor, very minor gap on the passenger side.
Also, what about the quality of the CF and clear coat? Has it hold up? Any bubbling?
And finally. Is it true that the fitment is very tight, which could potentially scratch the paint, and that you have to drill holes to make it fit properly?
Im asking because a different made this comments and I would like to see if this is the same with everyone.
I would appreciate a reply. Thanks.
#55
Hey blackvitzrs,
You have a very nice GE Fit. I was wondering on the fitment on the JDP diffuser, as some other members have said its not 100%. That there's a minor, very minor gap on the passenger side.
Also, what about the quality of the CF and clear coat? Has it hold up? Any bubbling?
And finally. Is it true that the fitment is very tight, which could potentially scratch the paint, and that you have to drill holes to make it fit properly?
Im asking because a different made this comments and I would like to see if this is the same with everyone.
I would appreciate a reply. Thanks.
You have a very nice GE Fit. I was wondering on the fitment on the JDP diffuser, as some other members have said its not 100%. That there's a minor, very minor gap on the passenger side.
Also, what about the quality of the CF and clear coat? Has it hold up? Any bubbling?
And finally. Is it true that the fitment is very tight, which could potentially scratch the paint, and that you have to drill holes to make it fit properly?
Im asking because a different made this comments and I would like to see if this is the same with everyone.
I would appreciate a reply. Thanks.
I was rear ended and the local body shop was able to track down another one. This one was much better quality wise. Fitment from what I can see is very good as well. I have no complaints on this new one.
Thread
Thread Starter
Forum
Replies
Last Post
whittenzack
2nd Generation GE8 Specific Fit Photos & Videos Sub-Forum
28
06-01-2013 11:33 PM
netekdenkow
2nd Generation (GE 08-13)
8
12-02-2010 01:49 AM
MK GD3
Fit Interior & Exterior Illumination
32
01-13-2008 11:09 PM