who has the weapon r header ge8
#42
I'm late to the party...
![Wavey](https://www.fitfreak.net/forums/images/smilies/wavey.gif)
555-too-sexy or Lyon, maybe you guys can chime in here...is the close-coupled cat onverter considered the primary cat and the under floor cat considered the secondary?
Yeah I agree that going to a muffler shop may be the most cost effective solution at this time. I'm waiting for some dyno charts from WR. Another possibility, maybe we could write (collectively...power in #'s) and have Honda Tuning do a power pages on this piece. They have done a prior power pages on the Fit (CAI, pulley, IK22 plugs) so this wouldn't be unreasonable.
Alternatively, we could do this ourselves with the new Iphone app i posted up earlier. This app gives Hp, 0-60, 1/4, 1/8 ET, etc.
Honestly though, I am reaching a cost vs. benefit plateau with the Fit. Cracking the ECU limits me from really pushing forward. At this time, IK22 + lightweight pulley + CAI is the only dyno proven mods on the Fit (this is good for around 10 hp...dyno results are posted in "Biggest Loser"). Chris, er...555sexy...has taken weight loss pretty far and probably has the most performance oriented Fit on this forum. I'd like to see your 0-60 and 1/4 mile times...are you planning on getting the Iphone app?
I think my weight loss is going to peak around 160-170 lbs. Getting to 200 lbs is going to require $2,000 in CF buckets...or chiseling out the sound deadening panels.
![Hyper](https://www.fitfreak.net/forums/images/smilies/hyper.gif)
![Hyper](https://www.fitfreak.net/forums/images/smilies/hyper.gif)
![Hyper](https://www.fitfreak.net/forums/images/smilies/hyper.gif)
I recently chiseled these out of my 2001 civic - the panels altogether weighed b/w 40-50 lbs:
![Name: Dryice.jpg
Views: 418
Size: 124.0 KB](https://www.fitfreak.net/forums/attachments/2nd-gen-ge8-specific-fit-engine-modifications-motor-swaps-ecu-tuning-sub-forum/42134d1501329236-who-has-weapon-r-header-ge8-dryice.jpg)
And after a lashing with the wire wheel:
![Name: Wirewheel.jpg
Views: 475
Size: 106.0 KB](https://www.fitfreak.net/forums/attachments/2nd-gen-ge8-specific-fit-engine-modifications-motor-swaps-ecu-tuning-sub-forum/42135d1501329236-who-has-weapon-r-header-ge8-wirewheel.jpg)
#43
Would disconnecting the rear O2 sensor (at the underfloor cat) throw a check engine light? I'd like to get the WR kit just for the first piece...then go all aluminum from there back...less expensive than titanium but equal or greater weight reduction.
Last edited by blackndecker; 09-28-2010 at 12:15 PM.
#44
Yes, it would, but you could always weld a bung onto the pipe, use an antifouler, and then screw the sensor into that.
#45
Ok here you all go I didnt know this thread was created. Anyhow here is the dyno result when we got our final version. The dyno is OEM vs WR Header both of which are going through the stock cat back exhaust system. We do not have a check engine light because of our CEL Eliminator.
![Name: 2010FitWRHeadervsOEM.jpg
Views: 413
Size: 85.7 KB](https://www.fitfreak.net/forums/attachments/2nd-gen-ge8-specific-fit-engine-modifications-motor-swaps-ecu-tuning-sub-forum/42122d1501329220-who-has-weapon-r-header-ge8-2010fitwrheadervsoem.jpg)
#46
Thanks for the dyno charts....those TQ gains almost seem too good to be true. Especially considering virtually every aftermarket exhaust available for the Fit causes an initial TQ and HP loss below 3500-4000 RPM. Someone please correct me if I'm wrong.
Question, what other mods were on the Fit when you dynoed?
Question, what other mods were on the Fit when you dynoed?
![Popcorn](https://www.fitfreak.net/forums/images/smilies/popc1.gif)
#48
After all the trouble it took to find a shop that could even do the balloon fittings properly and still have it leak I'm changing my tune. Save your time and get the WR one. Heck I'm probably going to end up getting one.
#50
The underfloor cat is secondary and only exists to help clean up the exhaust a little bit further. With the 2nd sensor existing before the actual cat, the ECU is not going to see whether the secondary cat is there or not. Reason why I ordered the J's front pipe to mate up with the rest of the J's exhaust.
I'm no tree-hugging hippie, but I would rather not pollute the air too much, already there is enough out and about that is not regulated filling the air with crap, that at least having the primary cat will still produce a much cleaner exhaust than some vehicles on the roads...or did the CFC program take all of them off the road and put people into Fits? hahahaha
I'm no tree-hugging hippie, but I would rather not pollute the air too much, already there is enough out and about that is not regulated filling the air with crap, that at least having the primary cat will still produce a much cleaner exhaust than some vehicles on the roads...or did the CFC program take all of them off the road and put people into Fits? hahahaha
#55
Ok here you all go I didnt know this thread was created. Anyhow here is the dyno result when we got our final version. The dyno is OEM vs WR Header both of which are going through the stock cat back exhaust system. We do not have a check engine light because of our CEL Eliminator.
![](http://i712.photobucket.com/albums/ww123/WeaponRproduct/2010FitWRHeadervsOEM.jpg)
![](http://i712.photobucket.com/albums/ww123/WeaponRproduct/2010FitWRHeadervsOEM.jpg)
Thread
Thread Starter
Forum
Replies
Last Post
GE8FTW
2nd Generation GE8 Specific For Sale/WTB Used Parts Sub-Forum
7
10-03-2015 12:04 AM
dantei136
Fit Engine Modifications, Motor Swaps, ECU Tuning
3
03-04-2014 10:32 PM
dantei136
Fit Engine Modifications, Motor Swaps, ECU Tuning
4
03-04-2014 07:24 AM